Quantcast
Channel: Intel Communities : Unanswered Discussions - Wired Ethernet
Viewing all 1749 articles
Browse latest View live
↧

intel driver update utility will find no drivers

April 28, 2017, 5:10 am
$
0
0

Hallo,

 

ich habe ein hp Notebook Elitebook8570w, mit einer 82579LM Gigabit Network Connection, die leider nicht mehr funktioniert. Die Treiberversion istv12.15.31.4 vom 25.7.2016.

Ich habe den aktuellen Treiber heruntergeladen, aber das Update gelingt weder über den Gerätemanager, noch über die Intel Software, auch nicht nach vollständiger Deinstallation ist der alte Treber nach der Installation wieder aktiv.

 

Ich habe jetzt das Intel Treiber Update Utility geladen und ausgeführt, das findet allerdings keinen Treiber.

 

Wie kann ich weiter vorgehen um das Problem zu isolieren, gibt es ein Hardware Tool um zu prüfen, ob da alles ok ist?

 

Vielen Dank :-)hp

↧
Search

I350 : Power consumption of SVR & LVR

April 28, 2017, 5:10 am
$
0
0

Hi all,

 

i'm confuse about this power consumption.

 

there are exist that power consumption table in the datasheet (11.5 current consumption)

 

but it is difference SVR & LVR electrical specifications written(11.6.9.1 & 11.6.9.3)

 

and what means about SVR's PWM mode & PFM mode?

 

nowhere explain about that in the datasheet

↧
↧

Intel I350 - boot Ubuntu without open-iscsi installed via Intel iSCSI Remote Boot

April 28, 2017, 9:02 pm
$
0
0

Dear all,

 

Is the open-iscsi installed in Ubuntu necessary for Intel I350 iSCSI Remote Boot?

 

Thanks.

↧

i210 DEV_OFF_N Enabling via iNVM

May 1, 2017, 8:45 am
$
0
0

I managed to enable the DEV_OFF_N functionality by programming an additional double word to the iNVM but I am not quite sure whether I did it properly and we do have the latest eepromARMtool as well as iNVM setting files available.

 

Programming the following double word into iNVM enables DEV_OFF_N incl. IEEE PHY power down:

83003C19

 

Does that make sense at all?

 

Even though table 2-8 of the i210 data sheet on miscellaneous pins states DEV_OFF_N being an asynchronous pin it seems to require a full PCIe hardware reset as well to actually really power off. I guess that is just the way it is supposed to be, correct?

 

The eepromARMtool we have is version 0.6.7 and the iNVM setting files are the v0.6 ones.

 

Are those current?

↧

Intel 218-v does not go above 100 mbp/s

May 3, 2017, 9:52 am
$
0
0

Hello there,

 

My Intel 218-v adapter has not been able to reach an internet speed higher than 100mbp/s.

My ISP provides a speed of 500 mbp/s.

 

When I put the 'Speed and Duplex' setting on 1GB it disconnects completely and with 'Auto Negotiation' it just gives a mere 100mbp/s and sometimes even switches to 10mbp/s.

 

I've tried different cables, but that did not turn out to be the problem. 
Installing the latest drivers didn't seem to help either.

 

Perhaps someone here knows a solution?

 

Kind regards,

Alex

↧
↧

ixgbe SFP+ 82599ES mtu higher than 1500 ERROR

May 5, 2017, 12:49 am
$
0
0

Hello

 

I have an Intel server with Ubuntu 16.04.2

 

02:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01)

02:00.1 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01)

 

I am unable to set mtu to a value higher than 1500, the error I get is:

SIOCSIFMTU: Invalid argument

 

 

I have downloaded and installed driver 4.6.4 and 5.0.4 and both DO NOT WORK

 

I have kernel

4.8.0-49-generic #52~16.04.1-Ubuntu SMP Thu Apr 20 10:55:59 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux

 

I have tried issuing the following commands:

ethtool -K eno4 rx-vlan-filter off

ethtool -K eno3 rxvlan off

ethtool -K eno3 txvlan off

 

But still cannot set the mtu to a different value.

 

Can anybody help?

 

Thanks

↧

Intel 82579LM Gigabit Phy & QM77 PCH - TCTL register and Tx functionalities

May 5, 2017, 2:52 am
$
0
0

Hello,

 

I'm working on the Intel 82579LM linked to a QM77 PCH (7/C210 Series Chipset).

 

When activating the Tx functionalities, using the TCLT register ( p193 of Intel® 82579 GbE PHY: Datasheet, Vol. 2.1 )

I noticed that if the "Reserved" "Read only" bit 28 was not specifically set to value '0b1', the Tx functionalities do not work.

 

Although I agree it is not "best-practice" to set "Reserved" bits, is this behavior normal ?

 

Many thanks !

↧

How to enable 25G line speed on XL710

May 7, 2017, 4:02 am
$
0
0

I am looking to enable 25G line speed on XL710

 

I am getting following support only

 

sudo ./qcu64e /NIC 1 /INFO
Intel(R) QSFP+ Configuration Utility

QCU version: v2.27.10.01
Copyright(C) 2016 by Intel Corporation.
Software released under Intel Proprietary License.

Adapter supports QSFP+ Configuration modification.
Current Configuration: 2x40

Supported Configurations:
1x40
2x40
4x10
2x2x10A (Top 2 lanes on Module0; Bottom 2 lanes on Module 1)
2x2x10B

 

# sudo ./qcu64e
Intel(R) QSFP+ Configuration Utility

QCU version: v2.27.10.01
Copyright(C) 2016 by Intel Corporation.
Software released under Intel Proprietary License.

NIC Seg:Bus Ven-Dev   Mode    Adapter Name
=== ======= ========= ======= ==================================================
1) 000:011 8086-1583 2x40    Cisco(R) Ethernet Converged NIC XL710-QDA2
2) 000:012 8086-1583 2x40    Cisco(R) Ethernet Converged NIC XL710-QDA2
3) 000:027 8086-1583 2x40    Cisco(R) Ethernet Converged NIC XL710-QDA2

Warning: No adapter selected.

↧
Search

Driver Installing for Intel PRO/1000 PT Quad-Port on Server 2016

May 8, 2017, 4:53 am
$
0
0

Hello,

 

I have a problem to install the current driver for my Intel Pro/1000 PT Quad PCIe Card on Server 2016 with Intel S5000PSL Mainboard..

When I use this Driver https://downloadcenter.intel.com/de/download/26092/Ethernet-Intel-Netzwerk-Adapter-Treiber-f-r-WindowsServer-2016-?product=83418 while the Installation Progress the System hangs up and froze. I have to make a hard reset.

When I use this Driver Download Intel® Ethernet-Adapter Verbindungen CD while the Installation Progress a message Comes and say's, that no Intel Products have been found.

 

Where can I get the proper Driver?

 

Please help!

Thank you.

↧
↧

Deployment Drivers Missing DEV_15D8

May 9, 2017, 8:22 am
$
0
0

Hi.

 

When deploying to the new 5th Gen Lenovo X1 Carbon, I keep getting an error stating that the network driver isn't installed - please see below:

pci ven_8086&dev_15D8&SUBSYS_224F17AA&REV_21

 

VEN_8086 = Intel

DEV_15D8 = UNKNOWN

 

I got the drivers here ( closest thing i could find ).

Download Intel Ethernet Gigabit Adapter Driver 12.15.24.1 for Windows 10 64 bit

 

Before the drivers weren't installed on the WIM file, so i used DISM to inject the drivers into the WIM file and managed to successfully boot from network

 

I installed the drivers and managed to the deployment screen to setup the deployment ready. Once the deployment is going and the windows 10 image has applied, before any of the applications can install i get the same error saying the network drivers hasn't been installed and you can see from the device manager that no network drivers have been installed, even Wi-Fi. Once on the machine, if i install the drivers from the link above, the Ethernet works fine.

 

Please can you let me know the correct drivers to use for the deployment of this network drivers.

↧

Can I use Direct Cable when connecting PC to PC?

May 10, 2017, 7:51 pm
$
0
0

When connecting PC and PC directly

In general, a cross cable is used.

 

 

I saw a PC to PC connection via a direct cable.

We confirmed that the ping test works normally.

 

 

There seems to be a separate LAN card to support this ...

 

 

Is there a way to check in the Network attribute?

Or is there a supported Chipset series?

↧

intel driver update utility will find no drivers

April 28, 2017, 5:10 am
$
0
0

Hallo,

 

ich habe ein hp Notebook Elitebook8570w, mit einer 82579LM Gigabit Network Connection, die leider nicht mehr funktioniert. Die Treiberversion istv12.15.31.4 vom 25.7.2016.

Ich habe den aktuellen Treiber heruntergeladen, aber das Update gelingt weder über den Gerätemanager, noch über die Intel Software, auch nicht nach vollständiger Deinstallation ist der alte Treber nach der Installation wieder aktiv.

 

Ich habe jetzt das Intel Treiber Update Utility geladen und ausgeführt, das findet allerdings keinen Treiber.

 

Wie kann ich weiter vorgehen um das Problem zu isolieren, gibt es ein Hardware Tool um zu prüfen, ob da alles ok ist?

 

Vielen Dank :-)hp

↧

RSS Support in IXGBEVF

May 15, 2017, 1:59 pm
$
0
0

I am using 3.3.2 ixgbevf in guest and 5.0.4 ixgbe on host. I noticed that even though there are two RX queues for each VF, but pretty much all the packets go to the first RX queue. The RSS related features are also not supported. How to turn on the RSS support on ixgbevf? If it does not support RSS, what's the point having multiple queues in ixgbevf?

 

root@ubuntu14:~# ethtool -n eth1

2 RX rings available

rxclass: Cannot get RX class rule count: Operation not supported

RX classification rule retrieval failed

root@ubuntu14:~# ethtool -x eth1

Cannot get RX flow hash indirection table: Operation not permitted

 

root@ubuntu14:~# ethtool -g eth1

Ring parameters for eth1:

Pre-set maximums:

RX: 4096

RX Mini: 0

RX Jumbo: 0

TX: 4096

Current hardware settings:

RX: 512

RX Mini: 0

RX Jumbo: 0

TX: 1024

 

 

root@ubuntu14:~# ethtool -k eth1

Features for eth1:

rx-checksumming: on

tx-checksumming: on

  tx-checksum-ipv4: on

  tx-checksum-ip-generic: off [fixed]

  tx-checksum-ipv6: on

  tx-checksum-fcoe-crc: off [fixed]

  tx-checksum-sctp: off [fixed]

scatter-gather: on

  tx-scatter-gather: on

  tx-scatter-gather-fraglist: off [fixed]

tcp-segmentation-offload: on

  tx-tcp-segmentation: on

  tx-tcp-ecn-segmentation: off [fixed]

  tx-tcp6-segmentation: on

udp-fragmentation-offload: off [fixed]

generic-segmentation-offload: on

generic-receive-offload: on

large-receive-offload: off [fixed]

rx-vlan-offload: on

tx-vlan-offload: on

ntuple-filters: off [fixed]

receive-hashing: off [fixed]

highdma: on [fixed]

rx-vlan-filter: on

vlan-challenged: off [fixed]

tx-lockless: off [fixed]

netns-local: off [fixed]

tx-gso-robust: off [fixed]

tx-fcoe-segmentation: off [fixed]

tx-gre-segmentation: off [fixed]

tx-ipip-segmentation: off [fixed]

tx-sit-segmentation: off [fixed]

tx-udp_tnl-segmentation: off [fixed]

fcoe-mtu: off [fixed]

tx-nocache-copy: off

loopback: off [fixed]

rx-fcs: off [fixed]

rx-all: off [fixed]

tx-vlan-stag-hw-insert: off [fixed]

rx-vlan-stag-hw-parse: off [fixed]

rx-vlan-stag-filter: off [fixed]

l2-fwd-offload: off [fixed]

busy-poll: on [fixed]

↧
↧

how to change the number of queues for i40e interfaces ?

May 17, 2017, 6:07 am
$
0
0

Hi all,

 

I would like to change the number of queues per interface (I use a split cable with a 4x10 configuration) with my XL710QDA1 and its i40e driver.

I couldn't find the options for modprobe I used to set with my ixgbe interfaces. Any Idea ?

 

Thanks,

 

Julien.

↧

PRO 1000 PT with Intel DH87RL motherboard

May 17, 2017, 6:17 am
$
0
0

Hi

 

I'm trying to install a network adapter Intel PRO 1000 PT on my motherboard DH87RL.

 

I put it on a PCI-E x16, led is blinking when I plug a wire, system is starting but the device doesn't show in BIOS (v0330).

 

Is there a known incompatibility within this device and my mother board ?

 

 

Thank you.

↧
Search

Termination of unused pairs when interfacing a I219LM to a 10/100 PHY.

May 17, 2017, 12:01 pm
$
0
0

When interfacing a I219LM to a 10/100 PHY, is it acceptable to leave the unused pairs as no connects, or is some manner of termination (Bob Smith?) required?

↧

i210 DEV_OFF_N Enabling via iNVM

May 1, 2017, 8:45 am
$
0
0

I managed to enable the DEV_OFF_N functionality by programming an additional double word to the iNVM but I am not quite sure whether I did it properly and we do have the latest eepromARMtool as well as iNVM setting files available.

 

Programming the following double word into iNVM enables DEV_OFF_N incl. IEEE PHY power down:

83003C19

 

Does that make sense at all?

 

Even though table 2-8 of the i210 data sheet on miscellaneous pins states DEV_OFF_N being an asynchronous pin it seems to require a full PCIe hardware reset as well to actually really power off. I guess that is just the way it is supposed to be, correct?

 

The eepromARMtool we have is version 0.6.7 and the iNVM setting files are the v0.6 ones.

 

Are those current?

↧
↧

X540-T2 NIC on DP67BG mainboard boot error

May 18, 2017, 8:16 am
$
0
0

Hi.

I recently purchased a X540-T2 card and tried installing it in my machine featuring a DP67BG mainboard. However it does not boot and halts with the port 80h code "27" ("Configuring memory"). In another machine the card works just fine. Are there any known issues regarding the combination of motherboard and NIC?

Thanks for your help, Moritz

↧

Re: igb Detected Tx Unit Hang

May 19, 2017, 12:47 am
$
0
0

Hi Experts,

 

i am facing similar issue with I350 4 ports

------------------------------------------------------------------------------------

kernel: [  918.176288] igb 0000:03:00.3: Detected Tx Unit Hang

kernel: [  918.176289]   Tx Queue <3>

kernel: [  918.176290] TDH <59>

kernel: [  918.176291] TDT <5a>

kernel: [  918.176292] next_to_use          <5a>

kernel: [  918.176293] next_to_clean        <59>

kernel: [  918.176294] buffer_info[next_to_clean]

kernel: [  918.176295] time_stamp <1000953e4>

kernel: [  918.176296] next_to_watch        <ffff880808ad2590>

kernel: [  918.176297] jiffies <100096ce1>

kernel: [  918.176298] desc.status <148000>

kernel: [  919.172375] ------------[ cut here ]------------

------------------------------------------------------------------------------

-----------------------------------------------------------------------------

Kernel  2.6.34.15

driver: igb

version: 5.3.0

firmware-version: 1.61, 0x8000091f

-----------------------------------------------------------------------------

Any suggestion?

 

Regards,

Sam

↧

ethernet drivers not working on NUC7I3BNH

May 21, 2017, 2:24 am
$
0
0

Hello

 

I cannot seem to install correctly my NUC7I3BNH, the intel ethernet drivers tell me that no card is detected in my NUC

 

Windows 10 used, with drivers downloaded on intel site.

8 gigs of RAM on one ram module, 256 gigs M2 hard drive

Last bios installed, since the install I cannot get into the bios by pressing F2 during boot sequence

 

Please advise

↧
Viewing all 1749 articles
Browse latest View live
Search
<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>